The Firehouse Tribune

View Original

Aerial Operations - The Aerial Truck Check, Part 1

Here is a look into how my Aerial truck check goes.

I usually start my Aerial truck check by walking around the Truck and checking for any obvious signs of an issue. Any issue, such as scratches dents, paint chips, doors missing, broken glass, you know the obvious things.

The next thing I do is go to the saw compartment. I take each of the gas- powered saws out of their compartment and start them. I allow them to idle outside is a position that they won’t wander off. If you don’t know what I mean here, just start a saw and place it on the ground in front of you. The saw will slowly wander off as it idles. So, place it in a crack in the ground or up against the wall of the firehouse. (NOTE: Make sure it doesn’t vibrate on anything that may become damaged, like paint on the firehouse wall.) I allow the saws to run the entire time I am checking the Truck. When Im done checking the truck, I fuel the saws, check bar and chain oil, and place them in service. The reason I do this with the saws is to allow them to run and get up to temp. It helps keep a healthy saw. Now there is a lot more to the saws here, but this is where I will stop for now.

Next thing I do is pull the truck out of the bay. I am going to check the engine fluids of the truck. Some trucks you have access points to allow you to do this. I prefer to raise the ladder and then raise the cab of the truck. This allows me to get eyes on the undercarriage. I check the fluids, oil, transmission, window washer, and the DEF. I will check Hydraulic oil and the generator fluids at this time as well.

Continuing under the cab, I check the belts, pulleys and anything bolted on the motor. Especially that alternator. I don’t know why but, these have a habit of losing bolts. In our Aerial class one of the things that we do is a truck check before operating the truck. We have found more than once, a loose or missing bolt and have had to send someone to get a bolt to continue the class.

Once the motor and it’s various parts are in working order I move on the exhaust, brakes, and springs. Making sure all are in tact with no “shiny” metal. This usually means there is something broken. Lets hope whatever is broken, let’s say a spring, that it is shiny and not all rusted, if it is rusty this means it has likely been broken for some time and maybe we missed it on our last truck check.


THE AERIAL TRUCK CHECK

While the cab is still up check the back side of the tires for any deformities low tread, bubbles, chunks missing. Remember these are Emergency Vehicles, not a fleet truck. If there are any issues at all document it and bring it to the attention of the proper person. For me it is an e mail to the maintenance supervisor and the OIC for the day.

As we continue under the cab we grab a creeper, if you have one, and begin to roll under the truck. Now with the Aerial up and the cab in the air it should be obvious to others there is a truck check going on, but to be safe place an Out of Service tag on the vehicle to your department SOG’s. This way you ensure that no one will run the truck while you are under it.

Continue to check for obvious issues, again broken springs and other hardware. Check the hydraulic lines, any coolant lines that may run here. Air brakes and the cans in the rear. It’s a good idea to drain the air tanks while you are here, this will remove the moisture from the air tanks and help prolong your airbrake system.

Look for anything leaking fluid. Investigate it. I know some trucks have their quirks but again these are Emergency Vehicles.

Check the inside tires for any issues, check air pressure on all tires, top off to your truck’s specifications.

Next month we will dive into the compartments of the truck and the aerial. Please remember this is just a way to do something and hopefully give you a few tips along the way. My approach is systematic and works for me. It may not all work for you. As always if you have something that may help, drop me an e mail and Ill put in here! Oh and BTW, the saws are still running, make them ready and put em back on the truck!